Basic Information
Technical Specification
We are Supplier, Exporter of Temperature Humidity Sensors & transmitters XD Series, Rotronic XD Series Humidity And Temperature Sensors, Rotronics XD series and our set up is situated in Pune, Maharashtra, India.
The HygroFlex1 series is the latest development in inexpensive HVAC transmitters for relative humidity and temperature. The devices are equipped with the tried-and-tested Hygromer IN-1 sensor and boast unbeatable value for money. The optional ROTRONIC SW21 software enables you to scale, calibrate and adjust ( only humidity ) the transmitter.
Technical Specification
| Versions | |
The HygroClip XD is available as standard probe or as industrial probe with remote sensor. The stan dard versions come in the colors black |
|
| Standard versions | |
| XD33 - S3X | Standard housing, black 0...1 V, -40...60 °C, UART |
| XD33 - W3X | Standard housing, white 0...1 V, - 40...60 °C, UART |
| Industrial versions | |
| XD33 - SC12D6 | Industrial housing, 2 m cable 0...1 V, 0...150 °C, UART |
| XD33 - SC15D6 | Industrial housing, 5 m cable 0...1 V, 0...150 °C, UART |
| Other configurations on request | |
| Analog output | 0...1 / 5 / 10 V, 0 / 4...20 mA |
| Interface | UART or RS-485 |
| Scale | Freely scalable |
| Typical accessories | |
| XD - AC3001 | Service cable to PC |
| E2-02XX | Extension cable with open ends, 2 m long, black |
| E3-02XX | Extension cable with open ends, 2 m long, white |
| HW4 | HW4 software for adjustment of the probe |
| NSP - PCB - PE40 | Polyethylene filter, gray |
| SP-S15 | Steel sinter filter ( ind. probe ) |
| ER-15 | Calibration device |
| EAxx - SCS | Humidity standards ( xx = % RH ) |
General Specification
| Device type | Humidity / Temperature probe | |
| Range of application measurement probe | -40...85 °C / 0...100 % RH | -100...200 °C * / 0...100 % RH * Short - term peak load |
| Accuracy at 23 °C, ± 5 K | 0.8 %RH / 0.2 K @ 5...24 VDC Adjusted at 23 °C and 10, 35, 80 % RH @ 5 VDC |
|
| Outputs | Analog ( voltage / current ), digital ( UART / RS - 485 ) | |
| Power supply | 5...16 VAC / 5...24 VDC ( 0...1 V ) 12...16 VAC / 16...24 VDC ( all kind of output signals ) |
|
| IP Protection | IP65 | |
| Technical Information | ||
| Current consumption | 7 mA ( typical ) @ 24 VDC, 0...10 V 12 mA ( typical ) @ 5 VDC, 0...1 V |
|
| Range of application electronics | -40...85 °C / 0...100 % RH | |
| Functions | ||
| Psychrometric calculations | Dew point / Frost point | |
| Adjustment via software | Single point, multipoint, dew point ( % RH / °C ), with service cable | |
| Prob | ||
| Filter | Polyethylene, 20 pm | No filter ex works |
| Filter carrier | Polycarbonate | Brass, nickel - plated |
| Maximum wind velocity | 20 m/s, with polyethylene filter | 3 m/s, without filter |
| Length of extension cable | 2 m / 5 m | |
| Maintenance / Calibration | Annual calibration ( recommended ) | |
| Humidity sensor | ROTRONIC HYGROMER® IN-1 | |
| Temperature sensor | Pt100 1/3 Class B | |
| Analog output | 0...1/5/10V | 0...1/5/10V 0/4...20 mA |
| Digital output | UART or RS - 485 | |
| Analog output | Accuracy at 23 °C, < 1 mV (1 V) / < 10 mV (10 V) / < 20 µA | |
| Response time - r63 | < 15s | |
| Long term stability humidity sensor | < 1% RH / year | |
| Conformities / Housing | ||
| CE / EMC compatibility | CE conformant 2007 / 108 / EG | |
| FDA / GAMP conformity | 21 CFR Part 11 / GAMP 5 | |
| Housing material | Polycarbonate | PEEK |
| Dimenstions probe head | ||
| Diameter | θ 15 mm | |
| Length | 135 mm | 100 mm / 250 mm 400 mm / 550 mm / 700 mm |
| Sensor Cable | - | 2 m / 5 m |